Do spa pumps have a reset button?

Locate the spa’s high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.

Why does my hot tub keep stopping?

Check for blockages, and clean or replace your filter. If that doesn’t help, check to see whether your circulation pump has power going to it. If it does, and it’s still not working, it may be time to replace the circulation pump. This code may also mean your pressure switch needs to be replaced.

Why is my hot tub not pumping up?

Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose. Pull out the cartridge filter to see if flow improves and the circulation pump is doing better.

How do you diagnose a hot tub problem?

Troubleshooting Common Hot Tub Issues

  1. Heater Failure. If the water in your spa isn’t as warm as it should it, it may be an indication of heater failure.
  2. Clogged Filter.
  3. Air Lock.
  4. Noisy Pump.
  5. Tripped GFCI Breakers.

Why does my hot tub cycle on and off?

The problem is usually diagnosable by the pulsating of the hot tub pump. The cause of a surging pump relates to filter problems, water levels, clogged lines, airlocks, and worn-out pumps. When you observe an irregular rate of water output from the spa jets, then it’s very likely that you have a surging pump.

Why does my lazy spa keep turning off?

Why does the spa switch off after 72 hours? This is a safety function. In order to reactivate the spa simply unlock the control panel by holding the lock/unlock key and then pressing the heater function.

How do I know if my spa pump is bad?

Symptoms of Spa Pump Failure There are several signs of hot tub pump failure: Humming noise from motor not turning, frozen shaft, bearings or impeller, or defective starting capacitor. Whining noise from worn bearings. Leaks under the pump from a failure of the pump seals.

How do I know if my circulation pump is working?

If you think you have a problem with your pump, try lightly touching it. If it’s working properly there will be a slight vibration and it will be warm to the touch. If your pump isn’t working, turn off its power supply and get a cloth and a screwdriver.

Why does my hot tub jets keep turning off?

Hot tub jets that are not working can be caused by air leaks, clogged drain covers, low water levels, dirty filters, bad pumps, improper jet adjustment, closed valves, electrical problems, clogged pump impeller, and issues with the hot tub controls. These issues should be troubleshot carefully.

Why choose Acura spa systems?

Acura Spa Systems offers replacement spa controls at very affordable prices. Our hot tub controls are energy efficient and turn on the spa heater only when it is necessary. We also manufacture replacement spa pumps with minimum amp draw.

How do I contact acuraspa support?

If you need technical assistance call us at 951-684-6667 or E-mail your questions to [email protected] and our experts will assist you with your questions. A $9.95 Handling charge is applied to all orders. All products sold per our “Terms and Conditions” found in the “Support” section of our menu.

Can your hot tub parts and accessories power my spa?

Our hot tub parts and accessories can power virtually any portable spa! Simply verify dimensions for direct drop-in replacement in your spa. We carry all materials in stock. Since 1987, we have powered over 1.3 million hot tubs of different names and brands. We can also power yours. Call us for any technical questions, 951-684-6667 x.223

Where can I get a replacement spa control?

Acura Spa Systems offers replacement spa controls at very affordable prices. Our hot tub controls are energy efficient and turn on the spa heater only when it is necessary. We also manufacture replacement spa pumps with minimum amp draw. DIY spa repair is very simple and straight forward.