How do I set up RAID Dell PowerEdge R720?

To configure the RAID controller on a Dell R720:

  1. Delete all existing disk groups: IMPORTANT:Remember, deleting a disk group also deletes the data on that disk group.
  2. Create a new disk group for the Forge system:
  3. Create a new disk group for the Forge failover VMs:
  4. Configure the VD disks: to fast initialize:

How many drives are needed for RAID 10?

four
RAID 10 is secure because mirroring duplicates all your data. It’s fast because the data is striped across multiple disks; chunks of data can be read and written to different disks simultaneously. To implement RAID 10, you need at least four physical hard drives. You also need a disk controller that supports RAID.

How do I create a RAID on my HP Proliant server?

HP EliteDesk and ProDesk PCs – Configuring RAID 1 with SATA RAID Controller

  1. Step 1: Prepare your computer. Prepare your computer before configuring the hard drives for RAID 1.
  2. Step 2: Update the BIOS. Install the latest BIOS version.
  3. Step 3: Setting the BIOS for configuring RAID 1.
  4. Step 4: Creating a RAID 1 volume.

How do I set up RAID Dell PowerEdge?

  1. Press the “F2” key during POST and launch the System Setup Menu.
  2. Click “Device Settings” on the System Setup screen.
  3. Select the RAID controller to be configured on the Device Settings screen.
  4. Click “Configuration Management” on the Main Menu.
  5. Click “Create Virtual Disk” on the Configuration Management screen.

How do you set up a RAID controller?

Configure RAID Controller in BIOS

  1. Reboot the server and press F2 when the Sun Logo appears.
  2. In the BIOS Setup utility dialog, select Advanced –> IDE Configuration .
  3. In the IDE Configuration menu, select Configure SATA AS , then press Enter.
  4. In the SATA Options menu, select RAID , then press Enter.

How many disks can RAID 10 lose?

A standard four-disk RAID 10 setup can only withstand one drive failure in each mirrored pair of disk drives. Otherwise, total data loss occurs. And as with the standard two-disk RAID 1 configuration, total storage capacity of RAID 10 is halved. So, six 1TB disk drives will only net you 3TB of usable space.

How do I get to RAID settings?

The RAID option must be enabled in the BIOS before the system can load the RAID option ROM code.

  1. Press F2 during startup to enter the BIOS setup.
  2. To enable RAID, use one of the following methods, depending on your board model. Go to Configuration > SATA Drives, set Chipset SATA Mode to RAID.
  3. Press F10 to save and exit.

How do I setup a RAID server?

How to configure RAID controller on a Dell R720?

To configure the RAID controller on a Dell R720: 1 On the Virtual Disk page, select an existing disk group, then press F2 to open the Operations dialog. 2 In the dialog, select Delete Disk Group. 3 Repeat Step 2.a.a and Step 2.a.b until all disk groups are deleted.

How do I create a RAID-5 or RAID-6 configuration?

Raid Level: Select RAID-5. If your hardware configuration consists of eight 4TB disk drives, select RAID-6. Physical Disks: Select all available physical disks. Disk sizes might vary. VD Size: Enter 300, the recommended size for the Forge System disk group. VD Name: Enter ForgeSystem. Click OK when these fields are completed.

How do I configure the PERC h710p RAID controller with multiple disks?

During the R720 boot sequence, wait approximately 24 seconds for this screen, then press Ctrl+R to launch the PERC H710P configuration utility. In the configuration utility, configure the PERC RAID controller with multiple logical disks spanning all six physical disks in a single RAID 5 array:

Do I need to set up RAID-5 on my H710?

If you’re insistent on keeping the H710 – you’re going to want to set up a RAID-0 virtual disk for each of your physical hard drives – Do not under any circumstances set up RAID-5 on the H710 and pass that through to FreeNAS!

By Advice